Specialized in R&D, mass production and OEM/ODM of automotive jump starters. Factory direct supply with consistent quality.
A car jump starter is a portable device built with a high-rate power lithium battery. Its core function is to deliver instant high current to crank the car engine when the vehicle battery is drained and fails to start. Most models also integrate additional features such as power bank, LED lighting, and emergency rescue functions. It is widely applicable to passenger cars, SUVs, commercial vehicles, construction machinery and more.
The core differences lie in discharge capability and safety design:
There are two core indicators to reference:
If you are unsure, you can provide your vehicle information for model selection assistance.
All our products have passed CE, FCC, RoHS and REACH international safety certifications, and comply with the latest EU PPWR (Regulation EU 2025/40) requirements. They can be legally exported to most countries and regions worldwide.
Standard operation steps are as follows:
Starting a normal-displacement passenger car consumes only about 3%-5% of the battery capacity. Taking a 12000mAh mainstream model as an example, it can support 20-30 consecutive starts on a full charge (actual number may vary slightly depending on ambient temperature and engine displacement).
Yes. All our models support dead battery start function. Even if the original car battery is completely dead with 0V, the jump starter can directly drive the starter motor to start the engine as long as it is sufficiently charged.
The product is rechargeable and reusable. The built-in power lithium battery has a cycle life of ≥1000 charges under normal use, and can serve stably for 3-5 years in typical usage scenarios.
No. All models are equipped with intelligent safety battery clamps with reverse polarity protection. If the terminals are reversed, the device will automatically cut off output and trigger sound and light alarm. It will not damage the vehicle circuit or the jump starter itself. You can use it normally after correcting the connection.
No. The product has 8 layers of safety protection circuits including overvoltage, overcurrent, short circuit and over-temperature protection. It delivers stable output voltage without impulse current that could damage vehicle ECU, onboard computer and other electronic components. It is safe to use.
The product adopts high-temperature resistant battery cells and protective structure design, with an operating temperature range from -20℃ to 65℃. Short-term placement inside the car will not cause safety issues. However, it is recommended to store it in a cool place inside the car and avoid long-term exposure to direct sunlight to prolong battery life.
A small spark at the moment of connection is normal, caused by instantaneous conduction when the clamp touches the battery terminal. It will not cause danger. If there is continuous heavy sparking, smoke or other abnormal conditions, please disconnect immediately and check for short circuit or equipment failure.
Displacement reference for standard 12V series:
24V series supports diesel engines up to 12L. Please refer to the corresponding product specification sheet for specific parameters.
All models are equipped with USB output ports, supporting fast charging for mobile phones, tablets, cameras, laptops and other digital devices. Some models support DC output to power on-board appliances. They also come with built-in LED emergency lights with three modes: steady on, strobe, and SOS distress signal.
For long-term storage, it is recommended to recharge the device every 3 months and keep the battery level between 50%-80% to maximize battery life. If used frequently, charge it timely according to usage frequency.
Common causes and solutions:
Steady red or flashing red indicates abnormal connection, commonly caused by reverse polarity, short circuit or poor contact. Please check if the positive and negative terminals are connected correctly and if the clamps are tightly secured. Steady green means normal status and the vehicle is ready to start.
The MOQ for regular stock products is 10 units. For OEM logo customization, the MOQ is 100 units. For packaging, function or appearance customization, the MOQ is calculated based on specific requirements. You can contact our sales team for a detailed quote.
Yes, we provide full-range OEM/ODM customization services, including logo printing, packaging design, parameter adjustment, function customization, and appearance tooling. We have a professional R&D team to support development for various customization needs.
Stock orders ship within 1-3 working days after payment. Custom orders take 15-30 working days generally, depending on the complexity of customization. The exact lead time shall be subject to order confirmation.
Yes, we can provide samples for testing. Sample fee is charged at ex-factory price, which can be deducted from subsequent bulk orders.
Under non-artificial damage conditions, we provide 12 months warranty for the whole unit, and 24 months warranty for the core battery component.
For non-artificial quality issues within the warranty period, we provide free repair or replacement service. For issues beyond warranty or caused by human damage, we provide repair service at cost price. You can contact your sales representative or after-sales support, and we will follow up promptly.
